Tips to PET Bottle Design with Handle for Edible Oil Bottle Packaging

By CHUMPOWER  2018/07/16
in twiter google facebook

Tips to PET Bottle Design with Handle for Edible Oil Bottle Packaging

PET is the material widely used for plastic consumer goods. Compare to glass, it is more strength and flexible. For both manufacturer and transport cost issues, it is more economic. Design is one of the key factors for PET Bottles in Edible Oil Bottle Packaging Industry. Especially the handle design is critical.

2 Most Common Handle Designs of PET Bottles for Edible Oil Bottle Packaging

It is common to find the edible oil bottle packaging with handle which can be further divided into "Handle pre-inserted bottle" and "Handle post-inserted bottle." Here are the introductions of Pre-inserted Handle and Post-inserted Handle of PET Bottles for Edible Oil Bottle Packaging.

● Handle pre-inserted PET bottle

Handle pre-inserted bottle

Pre-inserted handle bottle is made by placing the handle in a mold through manipulator and the fitting place of the handle will be wrapped directly during the blowing. Therefore, the handle bottle would carry more force and it is usually used for larger capacity.

● Post-inserted handle PET bottle

Post-inserted handle bottle Post-inserted handle bottle

Handle post-inserted bottle is made by cavity insert, allowing the preformation of the handle fitting place. After the completion of blow molding, the handle is then placed into the finished bottle.

In the design of the handle bottle, the handle's position is critical since the handle mounted above the body (the middle) is easier for pouring the content. In addition, the handle shall be buried in the body or there shall be strip added on both sides of the bottle body where the handle located to keep it from shaking. In order to accommodate the handle, both sides of the bottle will be too large. Therefore, a pattern or strip is required to strengthen the intensity. By doing so, there will not be the deformation of the water bottle or oil bottle when it is picked up. The parting surface is normally at the handle and the pouring route is generally straight line to prevent from inverting.

Edible Oil Bottle with Handle Design

(A) Note whether the space of this area is good enough for blow molding. Should the good molding be not available, the handle will get loose easily.
(B) The compatible place of the handle and the bottle's body shall be tangent instead of undercutting to avoid interference.
(C) The distance of undercutting is 1mm.
(D) Increase the length by 1mm.
(E) The compatible place of the handle's tenon, R angle, should not be too small to avoid the bad molding of the tenon's compatible place and therefore getting the handle loose easily.

Edible Oil Bottle with Handle Design

There should be a certain space between the handle and the preform to avoid the interference between them.

4 Key Concerns to Design a Perfect Handle for PET Edible Oil Bottles

1. Handy design

A handy design with PET Packaging Bottles of Edible Oil and prevents the hand from slipping over.

2. Break-resistant

When there is too much oil in the PET Bottle and it is too heavy to dump, a break--resistant handle design reduces the deformation of PET Bottles.

3. Low-cost production

Efficient output is always the key for plastic bottling production lines. To optimize handle design of PET bottles brings the cost benefit.

4. Light weight

A light weight PET Bottle design for oil is one of the best solutions for Edible Oil Packaging, which can lead to substantial saving. It is a trend for a latest design by using of lightweight built-in PET Bottle Handle.

Videos of PET Bottle Design with Handle for Cooking Oil 

Learn more videos about our PET Bottle Design with Handle for Edible Oil Bottle Packaging.
CPSB-2000L (With bottle discharge conveyor) video

CHUMPOWER MACHINERY CORP. has over 20 years of experiences in the expertise of PET blow molding machine manufacturing apart from providing the appropriate blow molding machine for oil bottles, we also provide the best expertise and consultant on the design of handle oil bottle from preform/mold designblow molding equipmentWhole Plant Planning Solutions. If you have any questions or would you like to request a quote, contact us today.

Article Classification